2023 2024 EduVark > Education Discussion > General Discussion


  #1  
June 21st, 2014, 01:20 PM
Super Moderator
 
Join Date: Mar 2013
SAIL Management Trainee (MT) Exam Sample Paper

Here I am looking for the Mechanical Sample Question paper of SAIL Management Trainee (MT) Exam, can you please provide me the same???

As you are looking for the Mechanical Sample Question paper of SAIL Management Trainee (MT) Exam, so here I am sharing the same with you

The chronological order of strokes in a four stroke petrol engine is
1] Suction stroke, working stroke, compression stroke and exhaust stroke.
2] Suction stroke, compression stroke, working stroke and exhaust stroke.
3] Compression stroke, working stroke, suction stroke and exhaust stroke.
4] Compression stroke, suction stroke, working stroke and exhaust stroke.
The enthalpy of steam is defined as
1] Difference of internal energy and product of pressure and volume.
2] Product of internal energy and pressure.
3] Sum of internal energy and product of pressure and volume.
4] Amount of heat change divided by the absolute temperature.
Which of the following operations can be performed using a drilling machine
A. Reaming B. Countersinking C. Spot Facing D.
Thread tapping
1] Only A, B and D 2] Only B, C and D 3] Only A, B and C 4] All of
these
Which of the following are the advantages of impulse turbine over reaction turbines
A. Occupies less space per unit power.
B. Compounding is not necessary for speed reduction as the rotor speeds are usually low.
C. Suitable for high power generation.
1] B and C only 2] A only 3] C only 4] A and C only
Maximum power transfer through line V1= 110 kv, V2= 100kv, X=22 ohm is
a 500 MW
b 500 KW
c 250 MW
d 250 KW
Ans 500 MW
Q.Which type of power plant requires maximum expenditure
a Hydel power plants
b Nuclear power plants
c Thermal power plants
d Gas based power plants
Q.Base load of a power station stands for
a 2-4 hoursday
b 4-8 hoursday
c 8-12 hoursday
d 12-24hoursday
Ans 12-24hoursday
Q.A wire is placed on the top of a transmission line to protect from
a surge high voltage
b Direct lightning strocks
c indirect lightnin strocks
d Switching over voltages
Ans Direct lightning strocks
Q.A wire is placed on the top of a transmission line acts as
a acts as a phase wire
b acts as neutral
c acts as a transmission wire
d acts as ground wire
Which of the following can be magnified by magnetic amplifier
(a) voltage
(b) current
(c) power
(d) none of above
The inductance is not used in lag network because of
(a) big size
b) time delay and hysteresis losses
(c) high reactance
(d) none of these
Saturation in a stable control system can cause
(a) conditional stability
(b) over damping
(c) low level oscillations
(d) high level oscillations
Excessive noise in control systems can cause
a) reduction in bandwidth
(b) reduction in gain
(c) saturation in amplifying stages
(d) oscillations
The type-0 system has
(a) net pole at the origin
(b) no pole at the origin
(c) simple at one origin
(d) two poles at the origin
In control systems, excessive bandwidth should be avoided because
(a) noise is proportional to bandwidth
(b) it leads to low relative stability
(c) it leads to slow speed of response
(d) none of these
In most systems, an increase in gain leads to
(a) larger damping ratio
(b) smaller damping ratio
(c) constant damping ratio
(d) none of these
A step function is applied to the input of a system and output is of the form y = t, the system is
(a) stable
(b) unstable
(c) not necessarily stable
(d) conditionally stable
The function of the safety resistor in ohm meter is to
(a) limit the current in the coil
(b) increase the voltage drop across the coil
(c) increase the current in the coil
(d) protect the battery
Which of the following instruments is free from hysteresis and eddy current losses
(a) M.l. instrument
(b) electrostatic instrument
(c) electrodynamometer type instrument
(d)all of these
The dielectric loss of a capacitance can be measured by
(a) Wien bridge
(b) Owen bridge
(c) Schering bridge
(d) Maxwell bridge
Reed frequency meter is essentially a
(a) recording system
(b) deflection measuring system
(c) vibration measuring system
(d) oscillatory measuring system
In measurements made using a Q meter, high impedance elements should preferably be connected in
(a) star
(b) delta
(c) series
(d) parallel
A digital voltmeter measures
(a) peak value
(b) peak-to-peak value
(c) rms value
(d) average value

Last edited by Neelurk; April 22nd, 2020 at 05:42 PM.
Similar Threads
Thread
SAIL management trainee paper for electronics
SAIL Management Trainee Model Question Paper
Question Paper Of Sail Management Trainee
Sail Sample Papers for Management Trainee Technical
Previous Question Paper of SAIL Management Trainee
SAIL Management Trainee Aptitude Paper
SAIL Management Trainee Question Paper ECE
Question Paper for SAIL Management Trainee
Previous question paper of Sail Management trainee PDF
SAIL Management Trainee Exam Previous year question paper
SAIL Management Trainee Exam previous year Question Paper
SAIL Management Trainee (MT) question paper
SAIL Management Trainee Exam Previous year question paper
SAIL Management Trainee Computer Awareness Sample question paper
Sail Technical Paper for Management Trainee



Quick Reply
Your Username: Click here to log in

Message:
Options



All times are GMT +5. The time now is 05:52 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by vBSEO 3.6.0

1 2 3 4 5 6 7 8