I have done B.Tech in Civil Engineering and now want to apply for JKSSB (Jammu & Kashmir Service Selection Board) Junior Engineer (Civil) Post and looking for detailed syllabus of written exam for this post so please provide me the same?

As you are looking for question papers of Junior Engineer Exam for Civil Engineering discipline conducted by Jammu & Kashmir Service Selection Board (JKSSB), so here I am providing following question paper:

JKSSB Question Paper for Junior Engineer (Civil Engineering)

1. The time dependent deformation on soil is known as?
(A) Crack
(B) Creep
(C) Cut
(D) Condensation
2. Which of the following rule in a network is true?
(A) Event can occur even if all activities leading to it
are not completed.
(B) An event can occur twice
(C) There can be dead ends
(D) There must be only single initial node
3. Grain size, viscosity, temperature and void ratio are
the important factors influencing which of the
following property of soil?
(A) Infiltration
(B) Seepage
(C) Permeability
(D) Porosity
4. The y component of velocity in a two dimensional
incompressible flow is given by v=2y. At the point
(0, 1) the x component of velocity u=0. What is the
equation for the x component of velocity?
(A) u=0
(B) u=2x
(C) u=-2x
(D) u=2y
5. Which type of operation in a network requires neither
any time nor any resources?
(A) Parallel
(B) Dummy
(C) Serial
(D) Redundancy
6. Irrigation canals are aligned along with which of the
following geographical feature?
(A) Straight line
(B) Valley line
(C) Contour line
(D) Ridge line
7. During the survey of metro rail line, it was observed
that a canal and drainage intersect at almost same
level, while aligning the metro line from one point to
another. What structure needs to be built for this
feature?
(A) Inlet and outlet
(B) A syphon
(C) Aqueduct
(D) A level crossing
8. Which theorem states that, “In any beam the
deflection at any point D due to load W at any other
point C is same as the deflection at C due to the
same load W applied at D”?
(A) Castigliano's theorem
(B) Conjugate Beam Theorem
(C) Strain Energy Theorem
(D) Maxwell's Reciprocal deflection theorem
9. Which of the following is NOT the displacement
(A) Slope deflection method
(B) Moment distribution method
(C) Kani's method
(D) Column analogy method
10. Ringelmann scale is used to
(A) Measure CO
(B) Measure SO2
(C) Grade density of smoke
(D) Grade automobile exhaust gas
11. The hourly variation factor is usually taken as
(A) 1.5
(B) 1.8
(C) 2
(D) 2.7
12. For water bound macadam roads in localities of
heavy rainfall, the recommended value of camber is
(A) 1 in 30
(B) 1 in 36
(C) 1 in 48
(D) 1 in 60

13. What is the dimension of dynamic viscosity?
(A) ML-1T -1
(B) MLT -1
(C) ML-1T
(D) MLT
14. What is the pH value of a water logged field, if the top
soil has become alkaline and water logged?
(A) 8
(B) 9
(C) 10
(D) 11
15. It was found that the critical angle of a dam against
seepage pressure with respect to normal was 45
degrees. According to Khosla creep theory, what can
you say about the structure?
(A) The dam is stable against seepage pressure
(B) The dam is stable against overturning
(C) The dam is stable against lateral pressure
(D) The dam is stable against heave pressure
16. What is the least count of a vernier scale?
(A) Difference of the smallest division of main and
vernier scales
(B) Sum of the smallest division of main and vernier
scales
(C) Value of one division of vernier scale divided by
the total number of division of primary scale
(D) Value of one division of primary scale divided by
the total number of division of vernier scale
17. A Plot of land measures 30 cm x 60 cm on a map
drawn to scale 1 cm= 50 m. What will be the area of
the map when placed on a topographical map drawn
to a scale of 1 cm = 600 m?
(A) 15.0 sq.cm
(B) 22.5 sq.cm
(C) 12.5 sq.cm
(D) 24.0 sq.cm
18. The hydraulic gradient line is sum of which of the
following terms?
(A) Pressure head, velocity head with respect to a
reference line
(B) Pressure head, datum head with respect to a
reference line
(C) Velocity head, datum head with respect to a
reference line
(D) Pressure head with respect to a reference line
19. The amount of residual chlorine left in treated water
is about
(A) 0.01 to 0.05 ppm
(B) 0.05 to 0.5 ppm
(C) 0.5 to 1.0 ppm
(D) 1.0 to 2.0 ppm
20. Which type of frame it will be, if it has 3 joints & 4
members?
(A) Deficient
(B) Perfect
(C) Redundant
(D) Efficient
21. If a rectangular bar has been subjected to torsion,
then maximum shear stress will occur
(A) At the centre
(B) At the corner
(C) At the middle of longer side
(D) Along the diagonal
22. What shall be the maximum Shear force in a simply
supported beam of span 3 m having a point load of 4
KN at the centre of the beam?
(A) 4 KN
(B) 2 KN
(C) 6 KN
(D) 8 KN

23. Slope deflection method can be used for analyzing
which of the following?
(A) Statically determinate Structure
(B) Statically Indeterminate Structure
(C) Unstable Structure
(D) Simply Supported Structure
24. What are the effects on the body with mass
immersed in a fluid which is under motion?
(A) Lift and drag
(B) Drag and friction
(C) Lift and friction
(D) Friction and shear
25. Creep is the
(A) Lateral movement of rail
(B) Vertical movement of rail
(C) Longitudinal movement of rail
(D) Difference in level of two rails
26. What is the moisture depth available for
evapotranspiration in root zone of 1 m depth soil,
if dry weight of soil is 1.5 gm/cc, field capacity is
35% and permanent wilting point is 15%?
(A) 450 mm
(B) 300 mm
(C) 200 mm
(D) 150 mm
27. What is the intensity of irrigation, if the total area of
the field is 1000 acres and the cultivable commanded
area is 65 acres?
(A) 6.50%
(B) 0.65%
(C) 65%
(D) 0.065%
28. For which of the following reasons, the water shed
line is abandoned for aligning an irrigation canal?
(A) It is densely populated
(B) The terrain is plain
(C) Canal is independent of river
(D) Irrigation canal is deep
29. Which one of the following failures is caused by loose
fish bolts at expansion joints?
(A) Angular break
(B) Crushed head
(C) Split head
(D) Transverse fissures
30. The actual velocity of water flowing through the voids
called as
(A) Seepage velocity
(B) Infiltration velocity
(C) Flow velocity
(D) Void velocity
31. What will happen if there is upward migration of water
table towards the capillary fringe and the atmospheric
pressure falls to the freezing point?
(A) Frost Bulb
(B) Capillary Heave
(C) Frost Heave
(D) Capillary Bulb
32. As per IS 456: 2000 recommendations, the latest
time by which the formwork can be removed from
columns, walls and beams is given by which of the
following choices?
(A) 10 hours
(B) 12 hours
(C) 16 hours
(D) 15 hours
33. On a stressed body there are points on which shear
stress is zero. These planes are known as
(A) Orthogonal planes
(B) Normal planes
(C) Shear planes
(D) Principal planes
34. The distribution mains are designed for
(A) Maximum daily demand
(B) Maximum hourly demand
(C) Average daily demand
(D) Maximum hourly demand on maximum day

35. The rail is designated by its
(A) Length
(B) Weight
(C) Cross-section
(D) Weight per unit length
36. In limit state design method, the limiting values of
the depth of neutral axis for Fe 415 steel is given by
which of the following equations?
(A) 0.53 d
(B) 0.48 d
(C) 0.46 d
(D) 0.36 d
37. Maximum value of 'throw of switch' for Broad gauge
track is
(A) 89 mm
(B) 95 mm
(C) 100 mm
(D) 115 mm
38. The method of analysis of distribution system in
which domestic supply is neglected and fire demand
is considered is
(A) Equivalent method
(B) Circle method
(C) Electrical analysis method
(D) Hardy-cross method
39. In Network Analysis the commencement or
completion of an activity is called
(A) Time
(B) Duration
(C) Event
(D) Period
40. To express sound levels in decibels, sound pressure
levels are usually adopted on a reference scale of
(A) 10 µPa
(B) 20 µPa
(C) 50 µPa
(D) 100 µPa
41. Two important constituents in composition of steel
used in rail are
(A) Carbon and Manganese
(B) Carbon and Sulfur
(C) Carbon and Silica
(D) Manganese and Phosphorus
42. Which one of these is used for measurement of base
line?
(A) Metric chain
(B) Invar tape
(C) Steel tape
(D) Engineer's chain
43. Which of the following is the Coulomb shear strength
equation?
(A) S= c + Ω cos φ
(B) S= Ω + c tan φ
(C) S= c + Ω tan φ
(D) S= Ω + c cos φ
44. Composite sleeper index is the index of
(A) Toughness and Wear resistance
(B) Strength and Toughness
(C) Hardness and Strength
(D) Wear resistance and Hardness
45. What shall be the back bearing of a line, if its fore
bearing is 280 degree?
(A) 80 degree
(B) 100 degree
(C) 190 degree
(D) 200 degree
46. What will be the curve lead for a 1 in 8.5 turnout
taking off from a straight B G track?
(A) 28.49 m
(B) 21.04 m
(C) 14.24 m
(D) 7.45 m

47. A round steel bar of overall length 20 cm consists of
two equal portion of 10 cm each having diameter of
4 cm and 5 cm respectively, if the rod is subjected
to a tensile load of 10 tones then what will be the
elongation (where modulus of elasticity
E=2Χ106Kg/cm2)?
(A) 1(1/16+1/25)/10π cm
(B) 2(1/16+1/25)/10π cm
(C) 3(1/16+1/25)/10π cm
(D) 4(1/16+1/25)/10π cm
48. If reinforcement in a beam is cut parallel to its length
in plan, the reinforcement will be represented in
section as which of the following options?
(A) Small darkened circle
(B) Two horizontal parallel lines
(C) Two crossed lines
(D) Two vertical parallel lines
49. What is the minimum clear cover (in mm) to the main
steel bars in column?
(A) 10
(B) 15
(C) 25
(D) 40
50. In the limit state design as per IS 456:2000, the
shape of the compressive stress block of concrete is
a combination of rectangular and
(A) Elliptical shape
(B) Circular shape
(C) Parabolic shape
(D) Trapezoidal shape

To get complete question paper, download the file........................

Attached Files

JKSSB Question Paper for Junior Engineer (Civil Engineering).pdf (173.6 KB, 225 views)