2023 2024 EduVark > Education Discussion > General Discussion


  #2  
May 3rd, 2017, 02:59 PM
Super Moderator
 
Join Date: Mar 2012
Re: Lecture Notes.Network Analysis.VTU

The notes for the Network Analysis topic for the Bachelor of Engineering in EEE discipline course at VTU has been provided below.

Analysis and Design:— consistent procedures for Improvement of reaction - (Basis of Research and Development exercises)

Investigation

Input Output or Excitation or Response

Pre requirements:

(i) A.C single stage circuits - section 2-ELE 15/25

(ii) Elementary Calculus-Part B and C - Mat 11

(iii)Differential Equations part C - MAT 21

(iv)Laplace Transform - part D – MAT 21

(v) Solutions of Simultaneous conditions by Kramars Rule

(vi)Simple Matrix operations with genuine numbers

Co-essential:

use of number cruncher (ideally CASIO fx 570ms or fx 991ms)

Books for Reference:


(i)Engineering circuit Analysis - Hayt, Kimmerily and Durbin for parts 1,3,4,6,7

(ii)Network Analysis - Van ValkenBerg-parts 5,6,7

(iii)Network and Systems - Roy Choudary - part 2

Arrange Analysis


System is a framework with interconnected electrical components. System and circuit are the same.

The main distinction being a circuit might contain no less than one shut way.

Sorts of Networks

Direct and Nonlinear Networks:


A system is direct if the rule of superposition holds i.e if e1(t), r1 (t) and e2(t),

r2 (t) are excitation and reaction matches then if excitation is e1 (t) + e2 (t) then the reaction is r1 (t)

+ r2(t).

The system not fulfilling this condition is nonlinear

Ex:- Linear – Resistors, Inductors, Capacitors.

Nonlinear – Semiconductors gadgets like transistors, soaked iron center inductor, capacitance of a p-n work.

Inactive and dynamic Networks:

A Linear system is inactive on the off chance that (i) the vitality conveyed to the system is nonnegative

for any excitation. (ii) no voltages and streams show up between any two terminals before any excitation is connected.

Illustration:- R,L and C.

Dynamic system:- Networks containing gadgets having inside vitality –Generators, intensifiers and oscillators.

One-sided and Bilateral:

The circuit, in which voltage current relationship stays unaltered with the inversion of polarities of the source, is said to be respective.

Ex:- R, L and C

On the off chance that V-I connections are diverse with the inversion of polarities of the source, the circuit is said to be one-sided.

Ex:- semiconductor diodes.

Lumped and Distributed:

Components of a circuit, which are isolated physically, are known as lumped components.

Ex:- L and C.

Components, which are not distinguishable for investigative reasons for existing, are known as appropriated components.

Ex:- transmission lines having R, L, C up and down their length.

In the previous care Kirchhoff's laws hold great yet in the last case Maxwell's laws are required for thorough arrangement.

Proportional:

A system is said to be proportional if when the areas of excitation and reaction are exchanged, the connection between them continues as before




Please find the file attached below which has the details notes on the Network Analysis topic for the Bachelor of Engineering in EEE discipline course at VTU
Attached Files
File Type: pdf Network Analysis Notes - VTU.pdf (630.4 KB, 212 views)


Quick Reply
Your Username: Click here to log in

Message:
Options



All times are GMT +5. The time now is 11:34 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by vBSEO 3.6.0

1 2 3 4 5 6 7 8