2023 2024 EduVark > Education Discussion > General Discussion


  #1  
April 9th, 2015, 01:15 PM
Unregistered
Guest User
 
Syllabus for BIS

Will you provide me the syllabus/paper pattern for Bureau Of Indian standards (BIS) exam as I want to appear in BIS exam and want to know pattern/syllabus of the exam?
Similar Threads
Thread
LL.M. Syllabus in MDS university Ajmer syllabus
What Is The Syllabus For APPSC Group 2 Syllabus
WBUT Ac Syllabus MBA Old Syllabus
ICSE syllabus and CBSE syllabus Differences

  #2  
April 10th, 2015, 08:48 AM
Super Moderator
 
Join Date: Mar 2012
Re: Syllabus for BIS

As you want I am here telling you about the syllabus/paper pattern for Bureau Of Indian standards (BIS)exam.

Bureau Of Indian standards exam question paper will be of two parts.

Total Questions :120 objective type

Part I – consists of 80 questions on respective technical discipline as mentioned
in the advertisement.

Part II – consists of 40 questions on aptitude/analytical reasoning including
English.


Standard of questions will be of the level of Graduate Engineer or Post Graduate Science.


Here I am providing you BIS Scientist Mechanical Sample Question Paper of Bureau Of Indian standards.

Sample paper :

The chronological order of strokes in a four stroke petrol engine is:
1] Suction stroke, working stroke, compression stroke and exhaust stroke.
2] Suction stroke, compression stroke, working stroke and exhaust stroke.
3] Compression stroke, working stroke, suction stroke and exhaust stroke.
4] Compression stroke, suction stroke, working stroke and exhaust stroke.

The enthalpy of steam is defined as:
1] Difference of internal energy and product of pressure and volume.
2] Product of internal energy and pressure.
3] Sum of internal energy and product of pressure and volume.
4] Amount of heat change divided by the absolute temperature.

Which of the following operations can be performed using a drilling machine?
A. Reaming B. Countersinking C. Spot Facing D.
Thread tapping
1] Only A, B and D 2] Only B, C and D 3] Only A, B and C 4] All of
these

Which of the following are the advantages of impulse turbine over reaction turbines?
A. Occupies less space per unit power.
B. Compounding is not necessary for speed reduction as the rotor speeds are usually low.
C. Suitable for high power generation.
1] B and C only 2] A only 3] C only 4] A and C only

Maximum power transfer through line V1= 110 kv, V2= 100kv, X=22 ohm is
a 500 MW
b 500 KW
c 250 MW
d 250 KW
Ans: 500 MW

Q.Which type of power plant requires maximum expenditure
a Hydel power plants
b Nuclear power plants
c Thermal power plants
d Gas based power plants

Q.Base load of a power station stands for
a 2-4 hours/day
b 4-8 hours/day
c 8-12 hours/day
d 12-24hours/day
Ans: 12-24hours/day

Q.A wire is placed on the top of a transmission line to protect from
a surge high voltage
b Direct lightning strocks
c indirect lightnin strocks
d Switching over voltages
Ans: Direct lightning strocks

Q.A wire is placed on the top of a transmission line acts as
a acts as a phase wire
b acts as neutral
c acts as a transmission wire
d acts as ground wire

Which of the following can be magnified by magnetic amplifier
(a) voltage
(b) current
(c) power
(d) none of above

The inductance is not used in lag network because of
(a) big size
b) time delay and hysteresis losses
(c) high reactance
(d) none of these

Saturation in a stable control system can cause
(a) conditional stability
(b) over damping
(c) low level oscillations
(d) high level oscillations

Excessive noise in control systems can cause
a) reduction in bandwidth
(b) reduction in gain
(c) saturation in amplifying stages
(d) oscillations

The type-0 system has
(a) net pole at the origin
(b) no pole at the origin
(c) simple at one origin
(d) two poles at the origin

In control systems, excessive bandwidth should be avoided because
(a) noise is proportional to bandwidth
(b) it leads to low relative stability
(c) it leads to slow speed of response
(d) none of these

In most systems, an increase in gain leads to
(a) larger damping ratio
(b) smaller damping ratio
(c) constant damping ratio
(d) none of these

A step function is applied to the input of a system and output is of the form y = t, the system is
(a) stable
(b) unstable
(c) not necessarily stable
(d) conditionally stable


Quick Reply
Your Username: Click here to log in

Message:
Options



All times are GMT +5. The time now is 12:53 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by vBSEO 3.6.0

1 2 3 4 5 6 7 8